-
Who this checklist is for
-
The 9-point supplier checklist
-
1. Don't accept "temperature regulating" — get the PCM content data
-
2. Waterproof and water-repellent are two different tests — ask for both separately
-
3. For breathability, know whether you're looking at RET or MVTR
-
4. Measure color consistency in Pantone TCX, with Delta E under 2
-
5. Private-label and trademark authorization: spell out who owns what
-
6. Strength testing needs to match the end-use direction
-
7. Verify certifications — the expiry date and the covered facility
-
8. Pre-production samples and bulk are not the same fabric
-
9. Put acceptance criteria in the purchase contract, not the email
-
1. Don't accept "temperature regulating" — get the PCM content data
-
Common mistakes
Who this checklist is for
If you're sourcing hardshell fabric, temperature-regulating fabric (including Outlast fabric used in jackets and midlayers), or any functional fabric under a private-label arrangement, this list is for you. It's built from four years of reviewing fabric lots before they hit production at an apparel brand — roughly 200+ lots a year, about 18% of which fail first inspection.
Nine checks. About 20 minutes per new supplier, maybe an hour if you're thorough. That's still cheaper than a single rejected lot.
The 9-point supplier checklist
1. Don't accept "temperature regulating" — get the PCM content data
Outlast fabric works through microencapsulated phase-change material embedded in the fiber — it absorbs heat when you get warm and releases it when you cool down. That whole mechanism came out of NASA-funded research on astronaut suits. But the amount of PCM in the fabric is what actually determines whether the function does anything.
Ask for the phase-change enthalpy per unit area, in J/g, measured by DSC (differential scanning calorimetry). In 2023, I saw a supplier put less than 0.5 gsm of Outlast material into a 180 gsm lining, wrapped it in beautiful documentation, and called it temperature-regulating. That amount is basically invisible on a human body. Request a per-lot test report — not a certificate that says "contains Outlast material."
2. Waterproof and water-repellent are two different tests — ask for both separately
Honestly, this is where I see half of new sourcing people get tripped up.
Waterproof = hydrostatic head, tested under ISO 811, measured in millimeters. Anything under 10,000mm isn't really a hardshell in my book. Water-repellent = surface beading, tested under ISO 4920 spray test, scored 1 to 5, and you want at least a 4 to start.
A fabric can hold 20,000mm of water pressure and still score a 2 on spray (usually means the DWR finish isn't there, or it falls apart after a few washes). I require both numbers on every spec sheet. "Excellent water resistance" is not a number.
3. For breathability, know whether you're looking at RET or MVTR
These are not interchangeable. RET comes from ISO 11092 — lower is better. MVTR comes from ASTM E96 — higher is better. Suppliers frequently mix results from both methods and quote whichever number looks nicer on the page.
Pick your standard first. Then require all data against that standard. Otherwise the report you get back won't be speaking the same language as the report you sent to your factory.
4. Measure color consistency in Pantone TCX, with Delta E under 2
Textile color reference is Pantone TCX, not the paper-card version. Delta E above 2 starts to be visible to trained eyes; above 4 and most people will notice.
Draw a line here: some suppliers will call Delta E 2.5 "within industry standard." It isn't. Brand-critical colors are usually held to ≤2, and darker technical fabrics can stretch to around 3. That number goes in the contract, not just in an email thread.
In my first year on the compliance side, I made the classic specification error — I assumed "waterproof" meant the same thing to every vendor. Cost us a $22,000 rework and pushed a launch window back by three weeks. Since then every PO carries an attached spec sheet.
5. Private-label and trademark authorization: spell out who owns what
Whether you're doing functional fabric private label or polyester oxford fabric private label, three things need to be nailed down before the PO goes out — whose brand goes on the label, who supplies the hang tags, and who secures the authorization for registered marks like Outlast.
I had a supplier assure me "the authorization is covered on our end." When I asked for the actual paperwork, there wasn't any. We were stuck two weeks before launch — not a fun call. Now I ask for the authorization file before we talk price.
One thing most buyers miss: the Outlast logo size and typeface on hang tags is part of the license agreement. You can't just print it however you like.
6. Strength testing needs to match the end-use direction
For hardshells, tensile is usually ASTM D5034 or ISO 13934, and tear is ASTM D1424. The number itself matters less than whether the testing direction lines up with how the fabric is loaded in the final garment.
A 40D nylon with strong weft numbers is fine for some uses — but if the piece is stressed along the warp (reinforcement zones, pack panels, anything with directional load), then weft numbers are just decoration. Match test direction to load direction and you'll avoid a category of problems entirely.
7. Verify certifications — the expiry date and the covered facility
OEKO-TEX Standard 100, bluesign, GRS — all of them are tied to specific facilities and specific production lines.
The common play is a supplier sending a group-level certificate when the dyehouse you're actually buying from isn't on the covered list. Easy fix: get the certificate number, log into the issuing body's website, and check. Five minutes, saves weeks.
8. Pre-production samples and bulk are not the same fabric
A lab dip runs on different yarn lots, a different dye bath, sometimes a different finishing line. Gram weight drifts. Hand feel changes. Color consistency gets harder to hold.
So run a separate pre-production approval — same yarn lot, same dye bath, same finishing line as the bulk order. I skipped this once. Now it's a standalone clause in every contract.
9. Put acceptance criteria in the purchase contract, not the email
Email says "Delta E ≤ 2," contract doesn't, and when the fabric shows up at 2.8 the supplier says they went by industry convention.
I've seen a contract that literally read "color differences to be confirmed by both parties" — every confirmation turned into a two-week argument.
Color tolerance, gram weight range, hydrostatic head, tear strength, spray rating — attach them to the PO as an annex. Boring, but it's the only thing that holds up when someone doesn't want to honor the spec.
Common mistakes
A few patterns I keep seeing.
- Equating high waterproof rating with overall performance. The harder you push waterproofing, the more breathability usually gives. A hardshell is a trade-off curve, not a single metric.
- Treating certification as a magic shield. Certificates are tied to facilities. A group-level certificate doesn't mean the plant making your fabric is covered.
- Using "trust" instead of a pre-production sample. Does not matter how long you've worked together — when a new dye bath or a new yarn lot shows up, re-run the sample. I watched a five-year vendor relationship go sideways because they moved to a different dyehouse and the color shifted two shades.
- Skipping sample approval under time pressure. I did this once. We had three hours before the mill released our slot, and normally I'd wait for the test report, but there was no time. Went on past relationship alone. It worked out that time. I don't want to do it again.
Five minutes of verification beats five days of correction. Old advice, but it's my bank account that keeps proving it.